Phone answered 24/7 · Louisville, KY and nearby communities

Call 24/7: (502) 305-4876
Beargrass Creek Water ResponseWater Damage Help · Louisville, KY

How Do Burst Pipes Happen in Winter?

Last updated October 31, 2026

The short answer

The Freeze and Thaw Cycle

Water expands by about 9 percent when it freezes. If a pipe is full of water and the temperature drops, ice forms and pushes against the pipe walls. The pressure builds until the pipe gives way, often at a joint or a weak spot. A burst may not be visible until the ice thaws and water starts flowing again, which can turn a hidden leak into a sudden flood.

The damage often happens after the freeze, during the thaw. As ice melts, it releases water through the crack, and that water can soak walls, floors, and belongings quickly. You might notice a drop in water pressure, strange sounds in the walls, or frost on exposed pipes before a burst occurs. If you spot these signs, shut off the main water valve right away.

  • Frost on exposed pipes
  • Reduced water pressure from a trickle
  • Unusual banging or gurgling in the pipes
  • Cold spots on walls or floors near plumbing
  • Damp patches or water stains appearing suddenly

Why Some Pipes Are More at Risk

Pipes in unheated spaces are most vulnerable. Attics, crawl spaces, garages, basements, and exterior walls often lack enough insulation. A pipe with a small flow of water is less likely to freeze than one that sits still, so a home that is vacant during winter is at higher risk. Similarly, pipes near drafty vents or gaps in the foundation are more exposed to cold air.

The material matters too. Older metal pipes can corrode and weaken over time, while plastic pipes may become brittle in extreme cold. The location of the pipe, the amount of insulation around it, and the severity of the cold all play a role. If you have had a freeze before, the same spot is likely to freeze again, so it pays to address the problem before the next cold snap.

How to Spot a Burst Early

A burst pipe often announces itself with a change in water flow. Turn on a faucet and listen for sputtering or reduced pressure, which can mean air is in the line from a nearby leak. Check for water stains on ceilings or walls, especially below bathrooms and kitchens. A musty smell can also develop as moisture seeps into building materials.

If you find a burst pipe, turn off the main water valve immediately to stop the flow. Then open the lowest faucet in the house to drain remaining water. Do not use electrical appliances near standing water, and call the pros to handle the cleanup and drying. Acting fast limits the spread of water and reduces the chance of mold growth.

  • Turn off the main water shutoff valve
  • Open all faucets to drain the system
  • Avoid walking through standing water with electronics
  • Document the damage with photos for your records
  • Call local water damage pros for extraction and drying

Prevention Steps to Take Before a Freeze

Insulating exposed pipes is one of the simplest steps. Foam pipe sleeves or heat tape can be wrapped around pipes in unheated areas. Seal gaps around vents, doors, and foundation openings where cold air can reach plumbing. Keep the garage door closed if water lines run through the garage, and open cabinet doors under sinks to let warm room air circulate.

If you plan to be away, set the thermostat no lower than 55 degrees Fahrenheit, even when the house is empty. Let a faucet drip slightly on very cold nights to keep water moving, and know where your main shutoff valve is so you can act quickly. If you live in Louisville, keep your shutoff valve location written down and share it with a trusted neighbor.

When to Call the Pros

After a burst, the cleanup is more than mopping up. Water can soak into drywall, wood, and insulation, leading to structural issues and mold. The pros use specialized equipment to extract standing water and dry out the structure with dehumidifiers and air movers. They can also map the moisture to know which materials need to be removed.

You might need to repair or replace drywall, flooring, or ceiling materials after the water is gone. A professional can assess the extent of the damage and guide you through the restoration process. If you have insurance, check your policy to understand what is covered. Policies vary, and your insurer decides what is covered.

Talk to someone now

Phones are answered 24/7 for Louisville and nearby communities.

Call Now (502) 305-4876

Frequently asked questions

At what temperature do pipes burst?

Pipes can freeze when the temperature drops below 32 degrees Fahrenheit, but bursts usually happen after prolonged exposure to temperatures in the teens or lower. The risk increases when the cold lasts for several hours and the pipe is in an unheated area.

Can a pipe burst without freezing?

Yes, pipes can burst from high water pressure, corrosion, or physical damage. But in winter, freezing is the most common cause. If you hear banging or see water stains with no freeze, you may have a different issue, so have a plumber inspect the system.

How long does a burst pipe take to cause damage?

Damage can begin very soon after water escapes. The longer water sits, the deeper it soaks into materials, increasing the risk of mold and structural weakening. Acting quickly to shut off the water and call the pros reduces the overall damage.

Call Now (502) 305-4876